Tag Archives: Taurus

Taurus 709 Slim Photo Review

22 Sep

I posted last week about finally purchasing a Taurus 709 Slim in 9 mm after spending a lot of time considering and looking at the various .380 pocket pistols. I found the LCP/TCP/P3AT all too small for me to easily handle, grip and shoot with confidence. Although the 709 is really too big to pocket carry in most situations, it is small enough (and SLIM enough!) to tuck easily into a waistband or a jacket pocket.

I have the model 709SS with a matte stainless slide. Here are the full specs on the 709:

  • Model : 709SS
  • Finish: Matte Stainless Steel
  • Status: Available
  • Caliber: 9 mm
  • Grips: Checkered Polymer
  • Capacity : 7 +1
  • Weight: 19 oz
  • Barrel Length: 3″
  • Frame: Compact
  • Action: DA/SA
  • Front Sight: Fixed
  • Length: 6″
  • MSRP: $498.00

I’ve had the pistol for about a week and have carried it a few times and spent some range time with it. Instead of doing a conventional written review, I thought I’d try a ‘photo review’ to bring out my impressions on the Taurus 709.

P1150211.jpg picture by dtm101

Taurus 709 Slim in 9mm Parabellum. The 709 is an attractively designed pistol with a number of nice features for CCW.

P1150212.jpg picture by dtm101

Left side of the Taurus 709 Slim showing the slide release, magazine release and safety. Unfortunately for us lefties, none of these controls are ambidextrous.

P1150213.jpg picture by dtm101

Racking the slide on the 709 is not difficult and the slide release locks the slide open upon firing the last round.

P1150217.jpg picture by dtm101

Field stripping the 709 is done via Glock style levers on the frame just above the trigger. You must pull the trigger to fully release the slide for removal so be absolutely sure there are no rounds in the chamber before disassembly..

P1150220.jpg picture by dtm101

The underside of the slide is machined well with no rough spots. When the slide is attached to the frame, there is very little movement/wobble.

P1150222.jpg picture by dtm101

The frame of the 709 is polymer with steel inserts for the slide rails and a steel barrel locking block. Interior components are on par (thickness and appearance) with other polymer pistols that I own.

P1150225.jpg picture by dtm101

The Taurus 709 (bottom) compared to the S&W M&P9. This photo doesn't really show the actual size difference between these two pistols. The 709 weighs approximately 10 oz less and is much more compact in carry mode.

P1150226.jpg picture by dtm101

The 709 placed on top of the M&P9 to show the dimensional differences between the two pistols. Again the photo doesn't do justice to the real size difference the you feel when handling them.

P1150229.jpg picture by dtm101

Taurus 709 (top) and S&W M&P9 (bottom). This photo does a nice job of showing how small and slim the 709 is in comparison to a full size service pistol.

P1150230.jpg picture by dtm101

The 709 fills the hand fairly well for a compact pistol. I fired 120 rounds during my first range session with the 709 and didn't experience any FTF or FTE issues. Recoil is snappy but I didn't find it difficult to manage.

P1150231.jpg picture by dtm101

I found the 709 to point naturally in my hand. 'Memory pads' on the frame work well to keep your finger off the trigger until ready to fire. I was able to shoot 3" to 3 1/2" groups at 15 yards with several brands of ammo including my own reloads.

P1150232.jpg picture by dtm101

While not really a pocket pistol, the 709 is quite compact and is easily concealable. I'm currently looking for an inside the waist band (IWB) holster for concealed carry.

P1150235.jpg picture by dtm101

One nice feature of the 709 is the manual thumb safety. Here it is pictured in the 'safe on' position. Also take note of the Glock-style safety incorporated into the trigger. The 709 has a two stage trigger with a rather long but light first stage followed by a short but heavy second stage. The second stage is heavier than I prefer but it's manageable. It also offers you 'second strike' capability where you can pull the trigger again double action style of for some reason you get a light primer strike the first time.

P1150236.jpg picture by dtm101

Thumb safety in the "safe off" position. As mentioned previously the safety is not ambidextrous and can be tricky to engage with a left handed grip. The magazine release can be seen in the bottom of the photo. It's not ambidextrous either but I was able to engage the release easily with my trigger finger. Magazines drop freely when the release is pushed.

P1150242.jpg picture by dtm101

The rear polymer sight is adjustable for both windage and elevation. My pistol shot quite low at 15 yards even with the rear sight fully extended. This is apparently a common problem with the 709. Taurus has offered to pay for shipping it to Miami for repair, but I'm not ready to part with the pistol for an extended repair period (I'd be interested in knowing whether anyone has found a commercial replacement front sight that would correct the problem). Just below the rear sight is the 'Taurus Security System' that can be engaged with a key to make the firearm in-operable.

P1150253.jpg picture by dtm101

There is a relatively large area around the feed ramp where the cartridge case is unsupported. I didn't have any issues with several brands of factory loads but I did experience case bulging with my reloads. The Taurus manual specifies the use of factory loads only and I would agree!

P1150249.jpg picture by dtm101

Several of my fired reloads exhibiting case bulging in the area of the unsupported feed ramp. These were 124 grain bullets over 5.3 grains of Unique which is a rather mild loading according to the Speer manual. I will be sticking to factory loads in the 709 in the future. I've not had any case bulging with these same reloads in my other 9 mm pistols.


My Pocket Carry Dilemma

14 Sep

I’ve been debating, ever since Ruger introduced the LCP, on what it was that I wanted in a pocket carry pistol. I handled all the offerings including the LCP, P3AT, TCP as well as the 380’s from Sig, Walther and Bersa. And I had the opportunity to shoot an LCP and a PPK.

To be honest, the LCP, P3AT and TCP all felt too small to me to hold comfortably. I’m left handed so I had difficulty in activating the slide release on the LCP and TCP (the Kel-Tec doesn’t have a slide release).

I’ve also been going through a ‘caliber reduction’ phase – or at least trying to limit the number of new calibers I add to my collection. Reason being I reload most of my own ammo so adding a .380 ACP to my arsenal would also require new dies, brass, powders and bullets.

I really like the overall fit and finish on the 709 (as an aside I also really liked the TCP, perhaps even better then the LCP).

So I ended up purchasing a Taurus 709 Slim (a .9mm). It’s only slightly bigger than the pocket pistols yet it fits much more comfortably in my hand. And I have a .9mm caliber pistol which I feel more confident with compared to a .380 if needed for self defense.

I’ve read some conflicting reviews on the 709 in the various web forums. Some work well and some apparently have had issues. I’m not clear on the percentages… whether it’s the same people with issues posting on every forum and blog or whether there are that many 709’s with problems. There also seemed to be a trend toward issues with early production runs vs. more recent production, at least in what I was reading.

Over the coming weeks I’ll be shooting and carrying the 709 and will post my impressions.

Why doesn’t Winchester or Springfield make an AR-15?

19 Jul

Today’s post is a rant of sorts…..

The popularity of the AR rifle seems to be increasing across the board. Go to a gun shop or the range on any given day and you’ll probably see more AR platform rifles than any other single type of rifle.

In recent years Remington, Smith & Wesson and Ruger have all developed successful AR rifle product lines. Even Taurus announced an AR in mid-2009 (pictured below, although I have not seen much discussion of it since).

So why don’t companies like Winchester or Springfield or Savage make an AR? Granted we already have an abundance of new and existing AR makers on the market, but imagine how wildly popular ‘black rifles’ from these manufacturers would be? It would seem easy (from my perspective sitting at a computer!) for any of these companies to either manufacture or source the parts needed to make top quality AR’s ‘worthy’ of their brand.

A National Match AR would fit perfectly into Springfield’s product line, right alongside their National Match M1A’s and match grade 1911’s. Savage has their Law Enforcement line of bolt action rifles that would be nicely complemented with an accurate AR.

As I’ve blogged before, I’m a Winchester fan and would be one of the first in line for a Winchester branded AR. Their parent company FN is under a contractual agreement to not sell AR rifles or parts to the public (I believe I have this stated correctly) so perhaps that contractual restriction also applies to Winchester.

Hopefully I’ll be pleasantly surprised to find that all these manufacturers are planning their own AR behind closed doors…  but I’m not holding my breath!

Free Taurus Shot Timer App for iPhone

12 Jul

Available in iTunes for the iPhone is a free Shot Timer app from Taurus. It’s not going to replace a PACT or Pocket Pro on the competition circuit, but I’ve tried the free app and it works well. Here is more info on the app from Taurus:


To express our gratitude to you for being a loyal Taurus customer, we would like to offer you FREE OF CHARGE the “Taurus Timer” An app for the Iphone that you can download to your phone from the iTunes store.

• Use the new “Taurus Shot Timer” to test your speed and accuracy.

• Easy to use both outdoors and indoors with our anti-echo technology.

• Review time between consecutive shots, shot count and total time shooting.

• Personalize the “Taurus Shot Timer” to your comfort with special settings such as start delay, sensitivity, par time and random start.